外形尺寸圖DIMENSION OF STRUCTURE DRAWING

產品特點PRODUCT TRAIT

無泄漏……無機械軸封部，所以不存在有泄漏。

輸出量精度……清水情況下，可獲得±1.5%的高精度。

可以自吸……常溫清水條件下，吸程為1米。

允許干運轉……工作腔為波紋管，因而可以干運轉。

壽命長……本腔采用耐曲折特殊配方材料的聚丙稀制成，可以經受數百萬次的往復運動。

耐腐性能好……泵本采用聚丙稀制成，閥門選用了特種配方的FPM、EPDM，耐各種酸、堿等腐蝕性液體。

液溫……藥水溫度60℃，超過50℃時，壓力為20℃時的1/2，超過40℃時液體的蝕性會增加，須注意。

NO leaskage ……For there is no mechanical sealing position, no leakage exists.

Precision of outler……±1.5%high precision can be achived at the condition of clean water.

Self-suction……suction range is 1 meter at the condition of normal atmosphere. temperature and clean water.

A llowed to dry rotation……For working chamber bag consists of bellows, dry rotation is allowed.

Long service life……The chamber is made from polyac-rylate that is anti-winding and special prescrription, it can withstａnd countless reciprocating motion.

Anti-corrosion……Pump body is made from polyacrylate valve adopts special EPDM, FPM, resisting various acid alkali and etc, corrosive liquids.

Liquid temperature……The maximum medicinal liquid temperature is 60℃ ,when it is over 50℃,the highest pressure is the half of that at 20℃ ,when it surpasses 40℃ ,the corrosiveness of liquid may be increased(take note of it).

結構圖  STRUCTURAL DIAGRAM

No．

       名稱Name          材質Materi al          數量Quantity

                     (DZ、DZN、DS型／DZR型)

1閥體      Body                    PP                    2

2升閥    Poppetvalve         EPDM．CSM．FPM              2

3波紋管   Bellows                  PP                    1

4連桿  Conneeting Bod            PP/POM                  1

5支撐軸    Spindle           1Cr18Ni9Ti                  1

6偏心輪    Crank(B)          1Cr18Ni9Ti/POM              1

7偏心套    Crand(A)          1Cr18Ni9Ti/POM              1

8螺母      Nut                     PP                    2

9尾罩    End House                ABS                    1

10支架    Trestle               PP/PA66                  1

11馬達     Motor                   ／                    1

技術參數TECHNICAL PARAMETER

用途

彩色膠卷．照片擴印、x光膠片．縮微膠卷、電影膠片等自動沖洗。

飲料售貨機用。

粘液調合、食品添加劑的定量添加。

電子基板印刷線路的蝕刻．清洗，印刷制版。

水處理的酸堿中和．凝析劑的投入。

電鍍液的定量補給。

廣泛應用於添加劑、漂白液等各種藥劑的定量注入。

Automatic development of colour film, expansion of photograph, X-ray film, microfilm, cinefilm and etc.

It is used in beverage vending machine.

Sticking liquid and mediation.

Quantitative replenishment of food additive.

The etching and cleaning of electronic basicplate printing circuit.

The neutralization of acid and alkali for water treatment the utilization of condensating separation agent.

Quantitative supply of electroplate liquid.

Widely used in quantitative priming of additive, bleaching liquid and medical agents.