不燃輕質板
不燃輕質板屬于新型節能環保綠色裝飾建材，經過*，大量的市場應用，不燃輕質板因其既具硬度，更具韌性的特點不僅可廣泛應用于中高檔建筑的吊頂、隔墻（弧度墻）、圓（方）柱包敷、鋼柱（梁）防火包敷、防火門內襯，重大長房的防火墻、幕墻內襯、大型風管、電纜橋架等，2002年起被逐步應用在建筑中的精裝潢、藝術裝飾、辦公家具、衛生間隔斷，辦公隔斷等，市場應用領域還在不斷的擴大。
Non-combustible Lightweight Board belongs to modem energy saving green building materials for decoration. Through a long term application in bulk, Non-combustible Lightweight Board is not only used widely for the suspended ceiling, partition wall （are wall）, round （quadrate） column wrap, steel column （girder） anti-fire wrap and interior liner of fire proof door of middle-top grade buildings, the fireproof wall, interior liner of curtain wall, large-sized air conduit and cable bridge frame of important workshops and so on, but also used gradually for fine decoration, art decoration, office furniture, toilet partition, office partition etc of buildings, Furthermore, its market application area is being expanded continuously.
實踐證明：“不燃輕質板”是一個深受設計師、工程施工單位和用戶青睬的防火、防潮、高強、隔聲、環保的理想建材，可與國外同類材料媲美，是國內同類材料中的中高檔品牌產品。
Practice has proved that “ Non-combustible Lightweight Board” is a sort of ideal building material with the features of fire proof, moisture proof, high strength, sound reduction and environmental protection that is deeply favored by designers, project construction units and consumers, Non-combustible Lightweight Board can match with the overseas materials of the same types and it is a sort of middle-top grade product among the domestic materials of the same types.
經上?？萍记閳笏綑z索：不燃輕質板的總體技術已達到*水平。
According to the information retrieval by Shanghai science & Technique Information Center, it can be concluded that Non-combustible Lightweight Board has reached the advanced world technique standard.
技術數據Technical Data
項目Test Item | 單位Unit | 數據Data |
燃燒性能Combustibility |
| 不燃A級（GB5464）Non-combustible（A）GB5464 |
密度Density | g/cm3 | 0.9-1.15 |
導熱系數Thermal Conductivity | W/（m.k） | 0.25 |
吸濕變形率Moisture Absorption | % | ≤0.28 |
抗凍性Freezing Resistance |
| 經過25次凍融循環無分現象 No delamination after 25 freezing cycles |
防霉防蛀功能Mildew &Moth Proof |
| 板為無機物具放蟲防霉防蛀功能 board belongs to Inorganic materials and has these functions |
抗反鹵型Impermeability | 12小時 | 無水珠、無返潮No water drop at the bottom |
抗折強度Bending Strength | Mpa | 干態16、濕態20Dry 16 Saturated 20 |
抗沖擊Impact Strength | Kj/㎡ | ≥5.7 |
耐火極限Fire-resistant Limit | min | 2×6mm 60 2×8mm 120 2×10mm 180 2×12mm 240 |
隔聲量Sound Reduction | db | 2×8mm 44 2×12mm 54 3×12mm 57 4×14mm 60 |
標準板長寬容差Parallel Deviation | mm | 2440×1220 5 2400×1200 5 |
標準板厚度容差Thickness Deviation | mm | 0.5 |
外觀Appearance |
| 正面平整光滑反面平整不光滑 One side: Flat and smooth The other side: Flat and rough |
導靜電板表面電阻率Surface Resistivity | Ω | ≤1×105-6 |
靜電耗散板表面電阻率Surface Resistivity | Ω | ≤1×108-9 |
上述數據依據國家部門的檢測報告。
不燃輕質板的安裝說明
Installation Instructions for Non-combustible Lightweight Board
1、 不燃輕質板（以下簡稱板）的構件制作（如墻、柱、吊頂?shù)龋?yīng)在干燥的氣候中進行。
2、 根據設計要求先安裝好輕鋼龍骨（或其他龍骨）骨架，并按施工規范檢驗骨架安裝合格。
3、 用自攻螺絲固定板、固定順序：
1） 劃線確定固定部位：在固定部位鉆預孔，孔徑比自攻螺絲的直徑要小1mm。
2） 用自攻螺絲固定板，先固定板的中間部位，在固定板的兩邊。
3） 自攻螺絲間距不大于200mm。
4） 板邊距與自攻螺絲中心須大于15mm，以增加牢度。
5） 板與板之間建議不留縫。
6） 自攻螺絲頭須沉入板面1mm，并要作防銹處理。
7） 建議采用自攻刮削螺絲，可使螺絲頭經過刮削的作用一次性下沉。
4、 在板墻上粘貼瓷磚：
1） 安裝工序同上。
2） 板縫用防水膩子批嵌。
3） 板面用防水涂料涂滿。
4） 用U型釘將一層機制金屬絲網復在墻面上。
5） 用1:2水泥砂漿刮糙至金屬網平。
6） 用同樣比例的水泥砂漿或瓷磚粘貼磁磚。
5、 歡迎咨詢
技術
Welcome to use Non-combustible Lightweight Board. Please carefully read the following installation instructions:
1） Determine the fixation part by making a line, and preliminarily make boreholes on the fixation with the borehole diameter being 1mm smaller than that of the self-tapping screws.
2） Again, use the self-tapping screws to fix the board, Firstly fix the middle part of the board and then fix the both sides of the board.
3） The space between the self –tapping screws should not be more than 200mm.
4） The space between the board edge and the center of the self-tapping screws must be larger than 15mm so as to increase fastness.
5） No seam between boards is preferred.
6） The had of the self-tapping screws needs to enter into the board surface till the depth of 1mm and it is required to carry out the rust-proofing treatment for the head.
7） It is suggested to adopt special self-tapping scrape screws so as to make the screw head be settled once through the action of scraping.
- Affix ceramic tiles on a board:
1） Other installation procedures are the same as the above-mentioned ones.
2） Treat flat seams with water proof putty.
3） Fully paint the board surface with water proof paint.
4） Cover the metope with a layer of machine-made wire net and U-nails.
5） Scrape with cement-sand slurry （1:2 proportion） until the metal silk screen smooth.
6） To atlix the ceramic tiles with the same proportion of cement-sand slurry of Special ceramic tile cementing glue.
Service hotline:
節能環保從www.weish。。ｎｅｔ開始，樂享低碳，超越奢華。WEISH威旭專業服務節能環保，幫助企業實現低碳經濟，節能創造價值！低碳： 廣州威旭環保科技有限公司客服,WEISH威旭:www.weish。。ｎｅｔ
